Skip to content

r2L8192-200cm#

The r2L8192-200cm Basler racer 2 L camera is equipped with a Gpixel GL7008 sensor.

Basler racer 2 L CXP Camera

Specifications#

General Specifications#

r2L8192-200cm
Resolution 8192 x 1 pixels
Sensor Type Gpixel GL7008
Monochrome Linear CMOS
Global shutter
Sensor Format 57.34 mm
Pixel Size (H x V) 7 x 7 µm
Max. Line Rate 200 kHz
(pixel format set to an 8-bit or 10-bit pixel format and exposure time set to minimum)
Product Family racer 2 L
Mono / Color Mono
Image Data Interface CoaXPress, 2x CXP-12 (2.5–12.5 Gbps per channel)
Pixel Formats See Pixel Format.
Sensor Bit Depth 12 bit
Synchronization Via hardware trigger
Via software trigger
Via free run
Exposure Time Control Via hardware trigger
Programmable via the camera API
Camera Power Requirements Power over CoaXPress (PoCXP): 24 VDC supplied via the camera's Micro-BNC (HD‑BNC) connector
19.2–28.8 VDC supplied via I/O connector
≈8 W (typical) @ 24 VDC
I/O Lines 3 differential general purpose I/O (GPIO) lines
Lens Mount M72x0.75-mount
Size (L x W x H) 36 x 80 x 90 mm
Weight 420 g
Conformity CE (includes RoHS), UKCA, FCC, KC, GenICam, CoaXPress 2.0, IP30
Software Basler pylon Windows (version 7.5 or higher)
Basler pylon Linux x86 (64 bit) (version 7.5 or higher)
Basler Framegrabber SDK Windows (64 bit) (version 5.11 or higher)
Basler Framegrabber SDK Linux x86 (64 bit) (version 5.11 or higher)
Accessories Accessories for your camera model
Availability and Pricing See the product page on the Basler website.

Relative Quantum Efficiency#

Gpixel GL7008 Relative Quantum Efficiency

Mechanical Specifications#

Camera Dimensions and Mounting Points#

Mechanical Dimensions (in mm) for racer 2 L Cameras

→ Download the CAD/technical drawing for your Basler camera.

Requirements#

Environmental Requirements#

Temperature and Humidity#

Description Temperature and Humidity
Housing temperature during operation 0–50 °C (32–122 °F)
Humidity during operation <1–80 %, relative, non-condensing
Storage temperature -20–80 °C (-4–176 °F)
Storage humidity <1–80 %, relative, non-condensing
Housing temperature according to EN 62368-1 max. 70 °C (158 °F)
Ambient temperature according to EN 62368-1 max. 30 °C (86 °F)

Heat Dissipation#

→ See Providing Heat Dissipation.

Electrical Requirements#

WARNING – Electric Shock and Fire Hazard / Risque de choc électrique et d'incendie

Unapproved power supplies may cause electric shock or fire or both. Serious injury or death may occur.

  • You must use power supplies that meet the Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) or the Electrical Source 1 (ES1) and Power Source 2 (PS2) requirements.

Les blocs d'alimentation non approuvés peuvent causer des décharges électriques ou des départs de feu, ou les deux. Celles-ci représentent un risque de mort ou de blessure grave.

  • Vous devez utiliser un bloc d'alimentation conforme aux exigences Safety Extra Low Voltage (SELV) et Limited Power Source (LPS) ou Electrical Source 1 (ES1) et Power Source 2 (PS2).
NOTICE – Incorrect voltage can damage the camera.

You must supply camera and I/O power within the safe operating voltage ranges specified below.

Do not use negative voltage for an I/O line.

Camera Power#

You can supply camera power via Power over CoaXPress (PoCXP) or via the camera's I/O connector using an external power supply (AUX power). If you supply power via both the CoaXPress interface and the I/O connector, power supply via the I/O connector (AUX power) takes precedence.

Info

If the power supply via the I/O connector is interrupted, power is provided via PoCXP. Once AUX power is restored, power is provided again via the I/O connector. This switchover can take several seconds. The time depends on the respective transition (AUX power to PoCXP or PoCXP to AUX power) and on the interface card or frame grabber used.

Be aware that the camera's internal power supply is interrupted during the switchover which will cause the camera to restart.

  • Power supply via Power over CoaXPress (PoCXP): 24 VDC
  • Power supply via I/O connector: The operating voltage is 24 VDC. As a minimum, 18.6 VDC must be supplied. To avoid damaging the camera, a maximum of 26 VDC must not be exceeded.

I/O Lines#

→ See I/O Control of racer 2 L Cameras.

Circuit Diagrams#

→ See I/O Control of racer 2 L Cameras.

Cable Requirements#

CoaXPress Data Cable#

Use high-quality CoaXPress data cables with a Micro-BNC (HD-BNC) plug at both the camera and the host side.

The data cables must comply with the CoaXPress Standard version 2.0. The following table shows CoaXPress data cable specifications.

CoaXPress Data Cable Specifications
Impedance 75 Ω ± 4 Ω
Maximum Return Loss -15 dB
Maximum Attenuation -17.9 dB
Frequency Range 1–6.25 GHz
Connector Micro-BNC (HD-BNC), 75 Ω type
Total DC Roundtrip Resistance <4.98 Ω
Cable Current Capacity 1 A (normal operation)
  • A maximum cable length of 30 m must not be exceeded.
  • If you want to use cables by other manufacturers, make sure to use CoaXPress-certified cables. These are always marked with the maximum speed they support.
  • Basler recommends using CoaXPress data cables from the Basler cable portfolio. There are CoaXPress data cables of various lengths available.

I/O Cable#

Physical Interface#

Camera Connectors and Status LEDs#

Camera Connectors

I/O Connector#

  • 12-pin Hirose micro receptacle (part number HR10A-10R-12P)
  • Recommended mating connector: 12-pin Hirose micro plug (part number HR10A-10P-12S) or equivalent

Micro-BNC (HD-BNC) Connectors#

Two Micro-BNC (HD-BNC) connectors according to the CoaXPress Standard version 2.0:

  • A master connector for transmitting image data, control signals, and configuration commands and for supplying camera power (Power over CoaXPress; PoCXP)
  • An extension connector for transmitting image data

Status LEDs#

The status LEDs indicate the status of their associated CoaXPress connection according to the CoaXPress Standard version 2.0.

LED States#

LED State Meaning
Off No power
Solid orange System booting
Red flashing at a frequency of 12.5 Hz System error (e.g., internal error)
Red flashing at a frequency of 1 Hz Powered, but no CXP cable connected
Alternating green/orange flashing at a frequency of 0.5 Hz Connection test packets being sent
Solid green Device/Host connected, but no data being transferred
Orange flashing at a frequency of 1 Hz Device/Host connected, waiting for event (e.g., trigger)
Green flashing at a frequency of 12.5 Hz Device/Host connected, data being transferred
Alternating green/orange flashing at a frequency of 12.5 Hz (shown for a minimum of 1 s even if the connection detection is faster) Connection detection in progress, PoCXP active
Orange flashing at a frequency of 12.5 Hz (shown for a minimum of 1 s even if the connection detection is faster) Connection detection in progress, PoCXP not in use

Connector Pin Numbering and Assignments#

Pin Numbering for the I/O Connector

Pin Line Function
1 - 24 VDC camera power
2 - 24 VDC camera power
3 Line 1 - General purpose I/O (GPIO) line 1, negative pin
4 Line 1 + General purpose I/O (GPIO) line 1, positive pin
5 - Ground for general purpose I/O (GPIO) lines
6 Line 2 - General purpose I/O (GPIO) line 2, negative pin
7 Line 2 + General purpose I/O (GPIO) line 2, positive pin
8 - Ground for camera power
9 - Ground for camera power
10 - Not connected
11 Line 3 - General purpose I/O (GPIO) line 3, negative pin
12 Line 3 + General purpose I/O (GPIO) line 3, positive pin

Info

  • Ground for General Purpose I/O (GPIO) lines (pin 5) and ground for camera power (pins 8 and 9) and are tied together inside the camera.

  • Always connect both pins for camera power (pins 1 and 2) and ground (pins 8 and 9).

Precautions#

→ See Safety Instructions (boost, racer 2 L).

Installation#

→ See Camera Installation.

→ See also Configuring CXP Line Scan Cameras and Frame Grabbers.

Features#

→ See Features.